Could anyone tell me why my Kenmore washer does not drain though it spins?
Q. My Kenmore washer does not drain. I suspect clogging in or near the water pump or broken belt. Would that be a reasonable guess? If so, how can check them or fix them?
Asked by james - Tue Mar 11 05:49:12 2008 - - 6 Answers - 0 Comments
A. If you can get to the outlet pump at the bottom you will find the outlet pipe attached to the pump with a spring clamp. You will need a pair of pliers to release the spring then pull the pipe off and check for blockage by pushing a bent coat hanger up it until it exits at the sink end. If it's clear of debris then check confines of the pump for debris or malfunction.
Answered by wheeliebin - Tue Mar 11 07:22:38 2008
Q. My Kenmore washer does not drain. I suspect clogging in or near the water pump or broken belt. Would that be a reasonable guess? If so, how can check them or fix them?
Asked by james - Tue Mar 11 05:49:12 2008 - - 6 Answers - 0 Comments
A. If you can get to the outlet pump at the bottom you will find the outlet pipe attached to the pump with a spring clamp. You will need a pair of pliers to release the spring then pull the pipe off and check for blockage by pushing a bent coat hanger up it until it exits at the sink end. If it's clear of debris then check confines of the pump for debris or malfunction.
Answered by wheeliebin - Tue Mar 11 07:22:38 2008
Kenmore washer model 1586 whinning noise during spin cycle but does not spin?
Q. I have a Kenmore washer machine model 15862400 that is whinning during the spin cycle but does not spin how can I fix this? What could it be? Has anyone else had this problem? The rubber coupling looks fine, found whining coming from water pump. How old was your washer, Joevette?
Asked by netboyfishing - Thu Jan 15 03:04:13 2009 - - 1 Answers - 0 Comments
A. I have a Kenmore that did the same thing and the cause was a rubber coupling that fits between the motor and the drum. If you are good with tools you can fix it yourself but if not the cost is not too bad. If you fix it be very careful not to damage the control panel when taking it off (if you need to take it off on your model). It only took about 30 or 40 minutes to fix mine. I think mine is roughly 10 years old.
Answered by joevette - Thu Jan 15 03:16:32 2009
Q. I have a Kenmore washer machine model 15862400 that is whinning during the spin cycle but does not spin how can I fix this? What could it be? Has anyone else had this problem? The rubber coupling looks fine, found whining coming from water pump. How old was your washer, Joevette?
Asked by netboyfishing - Thu Jan 15 03:04:13 2009 - - 1 Answers - 0 Comments
A. I have a Kenmore that did the same thing and the cause was a rubber coupling that fits between the motor and the drum. If you are good with tools you can fix it yourself but if not the cost is not too bad. If you fix it be very careful not to damage the control panel when taking it off (if you need to take it off on your model). It only took about 30 or 40 minutes to fix mine. I think mine is roughly 10 years old.
Answered by joevette - Thu Jan 15 03:16:32 2009
Is there a regulator for a Kenmore washer?
Q. I have a Kenmore 110.26812690. My washer dumps too much water too quickly and it backs up my houses old plumbing. Is there a restrictor/regulator part which can be installed onto my discharge hose which will lessen the amount of water entering my system?
Asked by George - Fri Apr 9 12:15:57 2010 - - 1 Answers - 0 Comments
A. I'm not aware of anything designed specifically for this but what I can tell you is that it won't harm the pump if you constrict the flow. Try the plumbing aisle at your local big box store. You should be able to find a suitable reducer in copper or PVC for example it looks like a 3/4"->1/2" copper reducer would fit in the end of my discharge hose.
Answered by Dirtmover - Sat Apr 17 08:16:03 2010
Q. I have a Kenmore 110.26812690. My washer dumps too much water too quickly and it backs up my houses old plumbing. Is there a restrictor/regulator part which can be installed onto my discharge hose which will lessen the amount of water entering my system?
Asked by George - Fri Apr 9 12:15:57 2010 - - 1 Answers - 0 Comments
A. I'm not aware of anything designed specifically for this but what I can tell you is that it won't harm the pump if you constrict the flow. Try the plumbing aisle at your local big box store. You should be able to find a suitable reducer in copper or PVC for example it looks like a 3/4"->1/2" copper reducer would fit in the end of my discharge hose.
Answered by Dirtmover - Sat Apr 17 08:16:03 2010
Which is better Whirlpool or Kenmore washer and dryers?
Q. I just purchased a home and it comes with a Kenmore washer and dryer set, however, I already have a Whirlpool washer and dryer set. I am wondering which one is better since I am going to be selling the other set. I have only had the Whirlpool set for a year and a half but I bought it used so it's about 2-3 years old. I have no clue how old the Kenmore set it. I really like the Whirlpool but they seem to have the same features to me. Please help me out!
Asked by Kristian G - Tue Sep 29 16:33:35 2009 - - 4 Answers - 0 Comments
A. A lot of the Kenmore sets are made by Whirlpool or GE, The Whirlpool set is about as good for the price as it gets. So to be on the safe side I would probably stick with the Whirlpool, you know the use of it for a year and a half anyway.
Answered by greg c - Tue Sep 29 16:39:55 2009
Q. I just purchased a home and it comes with a Kenmore washer and dryer set, however, I already have a Whirlpool washer and dryer set. I am wondering which one is better since I am going to be selling the other set. I have only had the Whirlpool set for a year and a half but I bought it used so it's about 2-3 years old. I have no clue how old the Kenmore set it. I really like the Whirlpool but they seem to have the same features to me. Please help me out!
Asked by Kristian G - Tue Sep 29 16:33:35 2009 - - 4 Answers - 0 Comments
A. A lot of the Kenmore sets are made by Whirlpool or GE, The Whirlpool set is about as good for the price as it gets. So to be on the safe side I would probably stick with the Whirlpool, you know the use of it for a year and a half anyway.
Answered by greg c - Tue Sep 29 16:39:55 2009
My Kenmore washer stopped spinning anyone know why ?
Q. It's a 10 year old Kenmore washer. Just stopped spinning but won't wash either although it wll fill with water. Is this a switch problem ? How can I see if it's a switch problem, I don't know where it is can anoyone help please ?
Asked by Wiskers - Sun Jan 24 16:35:22 2010 - - 2 Answers - 0 Comments
A. I'm sure your washer is direct drive, and made by Whirlpool. A common problem with them, is the coupling between the motor and transmission break. It is a fairly easy thing to fix if you or someone you know has some mechanical ability. Here is a site that shows what to look for, and how to fix it, along with a video, if that is the problem. ...Good Luck...
Answered by Ret68 - Sun Jan 24 17:58:09 2010
Q. It's a 10 year old Kenmore washer. Just stopped spinning but won't wash either although it wll fill with water. Is this a switch problem ? How can I see if it's a switch problem, I don't know where it is can anoyone help please ?
Asked by Wiskers - Sun Jan 24 16:35:22 2010 - - 2 Answers - 0 Comments
A. I'm sure your washer is direct drive, and made by Whirlpool. A common problem with them, is the coupling between the motor and transmission break. It is a fairly easy thing to fix if you or someone you know has some mechanical ability. Here is a site that shows what to look for, and how to fix it, along with a video, if that is the problem. ...Good Luck...
Answered by Ret68 - Sun Jan 24 17:58:09 2010
my kenmore washer has a new belt and it made a strange noise and now when it starts, all it does is make a hum?
Q. my kenmore washer has a new belt and the other day it made this strange noise like fireworks going off and started to smoke. I shut it off. From that point on it just sits there and makes a humming sound and does nothing. Am I right in guessing the capacitor is bad?
Asked by deliguy35 - Wed Oct 22 05:16:11 2008 - - 1 Answers - 0 Comments
A. It sounds like the belt was installed too tightly, and this either cooked the bearing, or the motor. It sounds like the motor wants to start (so probably not the capacitor). You can test this by removing the belt and see if the motor runs unloaded. If it does start, you need bearings.
Answered by Terry D - Wed Oct 22 09:38:35 2008
Q. my kenmore washer has a new belt and the other day it made this strange noise like fireworks going off and started to smoke. I shut it off. From that point on it just sits there and makes a humming sound and does nothing. Am I right in guessing the capacitor is bad?
Asked by deliguy35 - Wed Oct 22 05:16:11 2008 - - 1 Answers - 0 Comments
A. It sounds like the belt was installed too tightly, and this either cooked the bearing, or the motor. It sounds like the motor wants to start (so probably not the capacitor). You can test this by removing the belt and see if the motor runs unloaded. If it does start, you need bearings.
Answered by Terry D - Wed Oct 22 09:38:35 2008
My Kenmore washer 80 series is pulsating water into the tub.?
Q. Please help! My washer is filling up little by little by pulsating water into the tub. After pulsating for a couple of minutes the hot will start coming in correctly. The cold refuses to work correctly at all. What does that sound like the problem is?
Asked by Stacy806 - Thu Nov 1 18:36:37 2007 - - 1 Answers - 0 Comments
A. Turn off both the hot water and the cold water. Unplug your washing machine. Pull it away from the wall. Have a bucket handy, and undo the water connections, one at a time, from the wall spigots. Drain each hose into the bucket. Undo each hose from the back of the washing machine, and take the hoses outside and flush them both ways with a garden hose. While the hoses are off, turn on the wall water spigots, one at a time. (Put your bucket under tap). This should drain the accumulated minerals and sand that may be in your lines. Then, hook the hoses back up securely to the machine first, then to the wall spigots. Turn the water on s-l-o-w-l-y. Look for leaks (meaning you didn't hook up securely enough.) When lines are secure, on, [cont.]
Answered by Cat Lady - Thu Nov 1 18:58:33 2007
Q. Please help! My washer is filling up little by little by pulsating water into the tub. After pulsating for a couple of minutes the hot will start coming in correctly. The cold refuses to work correctly at all. What does that sound like the problem is?
Asked by Stacy806 - Thu Nov 1 18:36:37 2007 - - 1 Answers - 0 Comments
A. Turn off both the hot water and the cold water. Unplug your washing machine. Pull it away from the wall. Have a bucket handy, and undo the water connections, one at a time, from the wall spigots. Drain each hose into the bucket. Undo each hose from the back of the washing machine, and take the hoses outside and flush them both ways with a garden hose. While the hoses are off, turn on the wall water spigots, one at a time. (Put your bucket under tap). This should drain the accumulated minerals and sand that may be in your lines. Then, hook the hoses back up securely to the machine first, then to the wall spigots. Turn the water on s-l-o-w-l-y. Look for leaks (meaning you didn't hook up securely enough.) When lines are secure, on, [cont.]
Answered by Cat Lady - Thu Nov 1 18:58:33 2007
Where do I find the model number on a Kenmore washer?
Q. The washer is about 6 or 7 years old and is called an Eco Care System washer. I took the panel off the bottom front of the washer and there is nothing. They have a repair chart inside the washer that shows the electrical circuit and such, and even on that chart is nothing that identifies my washer. Where oh where is that model number to be found? Reason why I need it is because I want to order myself another manual... Thank you!
Asked by Mybabysmomma - Fri Mar 26 14:27:05 2010 - - 4 Answers - 0 Comments
A. inside of lid, beneath the lid in the center, above the timer just over the top, on the back side of the console. Good luck.
Answered by Missy - Fri Mar 26 20:26:29 2010
Q. The washer is about 6 or 7 years old and is called an Eco Care System washer. I took the panel off the bottom front of the washer and there is nothing. They have a repair chart inside the washer that shows the electrical circuit and such, and even on that chart is nothing that identifies my washer. Where oh where is that model number to be found? Reason why I need it is because I want to order myself another manual... Thank you!
Asked by Mybabysmomma - Fri Mar 26 14:27:05 2010 - - 4 Answers - 0 Comments
A. inside of lid, beneath the lid in the center, above the timer just over the top, on the back side of the console. Good luck.
Answered by Missy - Fri Mar 26 20:26:29 2010
Kenmore washer leaking oil from gearcase and not agitating or spinning during cycle.?
Q. Washer Model #22292100 Serial# cp4680782 The water drains just fine and the timer advances but now all I hear is a loud clicking that sounds much like metal gears. What is the problem and how do I fix it?
Asked by Gabe A - Wed Apr 23 00:43:52 2008 - - 2 Answers - 1 Comments
A. The drive coupler between your motor and transmission is broke... This is a common problem... A drive coupler costs about $12... If your not familar on how to remove the case off of the washer then I would recomend you call a service tech or go online for directions...
Answered by Kirk D - Wed Apr 23 00:59:38 2008
Q. Washer Model #22292100 Serial# cp4680782 The water drains just fine and the timer advances but now all I hear is a loud clicking that sounds much like metal gears. What is the problem and how do I fix it?
Asked by Gabe A - Wed Apr 23 00:43:52 2008 - - 2 Answers - 1 Comments
A. The drive coupler between your motor and transmission is broke... This is a common problem... A drive coupler costs about $12... If your not familar on how to remove the case off of the washer then I would recomend you call a service tech or go online for directions...
Answered by Kirk D - Wed Apr 23 00:59:38 2008
Why does my Kenmore stackable washer spin out of control?
Q. I have a Kenmore stackable washer about 3 years old and every spin cycle it spins out of control. The bucket hits the side and bangs and makes the whole washer move. I have tried smaller loads, im about to try it empty and see what happens. I do know that the washer is not level from front to back. Can that cause this? Does anyone have any idea what it can be? All help would be great as we have just purchased this a couple months back. Chris
Asked by Chris S - Mon Apr 27 01:50:26 2009 - - 5 Answers - 0 Comments
A. more than likely your springs are broken or bad. go to www.searspartsdirect.com put your model # in and go the section marked base. it will show the springs. yours probably have ones that look like shock absorbers on a car they are that large. they costs about 80.00 each. you can buy them online and fix yourself if you have a handyman that can help you or you can call around to your local appliance parts store and purchase them.
Answered by Sandy - Mon Apr 27 06:35:18 2009
Q. I have a Kenmore stackable washer about 3 years old and every spin cycle it spins out of control. The bucket hits the side and bangs and makes the whole washer move. I have tried smaller loads, im about to try it empty and see what happens. I do know that the washer is not level from front to back. Can that cause this? Does anyone have any idea what it can be? All help would be great as we have just purchased this a couple months back. Chris
Asked by Chris S - Mon Apr 27 01:50:26 2009 - - 5 Answers - 0 Comments
A. more than likely your springs are broken or bad. go to www.searspartsdirect.com put your model # in and go the section marked base. it will show the springs. yours probably have ones that look like shock absorbers on a car they are that large. they costs about 80.00 each. you can buy them online and fix yourself if you have a handyman that can help you or you can call around to your local appliance parts store and purchase them.
Answered by Sandy - Mon Apr 27 06:35:18 2009
Kenmore washer broken coupler help?
Q. I have a kenmore washer about 7 years old. It fills with water and will drain--doesn't agitate or spin. After searching yahoo answers, I am sure it is a broken motor coupler. There are pieces of black rubberlike material under the washer. I (60 year old female who dapples in own repair work) have gotten the washer apart and have taken the two clips off for the pump. I can wiggle the pump---but how hard should I pull---I am afraid to break it. After that I think there are 2 screws and clips for the motor and the coupler should be there--and off to appliance part store I go. My son says to wait until he is here in two weeks--but I would rather fix it myself. Hopefully, I won't need to call a repair man as they would charge a fortune just… [cont.]
Asked by sam - Sun Aug 19 17:42:20 2007 - - 7 Answers - 0 Comments
A. your doing the job exactly right...just go ahead and pull it off...sometimes it will be hard because the motor shaft could have rusted into the pump shaft some but this isnt a major problem.spray some penetrating oil on it ..when you go to the parts store the coupling is the same one that whirlpool uses as they make that washer for kenmore...
Answered by wwwstat - Sun Aug 19 20:31:32 2007
Q. I have a kenmore washer about 7 years old. It fills with water and will drain--doesn't agitate or spin. After searching yahoo answers, I am sure it is a broken motor coupler. There are pieces of black rubberlike material under the washer. I (60 year old female who dapples in own repair work) have gotten the washer apart and have taken the two clips off for the pump. I can wiggle the pump---but how hard should I pull---I am afraid to break it. After that I think there are 2 screws and clips for the motor and the coupler should be there--and off to appliance part store I go. My son says to wait until he is here in two weeks--but I would rather fix it myself. Hopefully, I won't need to call a repair man as they would charge a fortune just… [cont.]
Asked by sam - Sun Aug 19 17:42:20 2007 - - 7 Answers - 0 Comments
A. your doing the job exactly right...just go ahead and pull it off...sometimes it will be hard because the motor shaft could have rusted into the pump shaft some but this isnt a major problem.spray some penetrating oil on it ..when you go to the parts store the coupling is the same one that whirlpool uses as they make that washer for kenmore...
Answered by wwwstat - Sun Aug 19 20:31:32 2007
I have a kenmore washer with a broken timer/knob-please help! How do I change it myself?
Q. The knob broke off on my washer, leaving part of the shaft in the washer panneling and another part stuck in the knob. I have a part, but I don't want(And can't afford) to have someone come in and repair it. It's urgant that someone please, if you know how to open the panneling, please tell me how to do that. I'm really in a bind.
Asked by Windeen S - Mon Dec 22 14:10:16 2008 - - 1 Answers - 0 Comments
A. Just unplug the washer and remove the control panel front.You should be able to get to the timer real easy then.Make sure you have the identical part and change one wire at a time.
Answered by Lee D - Mon Dec 22 15:00:21 2008
Q. The knob broke off on my washer, leaving part of the shaft in the washer panneling and another part stuck in the knob. I have a part, but I don't want(And can't afford) to have someone come in and repair it. It's urgant that someone please, if you know how to open the panneling, please tell me how to do that. I'm really in a bind.
Asked by Windeen S - Mon Dec 22 14:10:16 2008 - - 1 Answers - 0 Comments
A. Just unplug the washer and remove the control panel front.You should be able to get to the timer real easy then.Make sure you have the identical part and change one wire at a time.
Answered by Lee D - Mon Dec 22 15:00:21 2008
Kenmore washer 80 series won't hold water?
Q. I've Kenmore washer 80 model # 110.92283800 and once I start the water cycle it will just drain that water. Water will not stay inside the washer... any sugggestions. Thanks I've Kenmore washer 80 model # 110.92283800 and once I start the water cycle it will just drain that water. Water will not stay inside the washer... any sugggestions. My drain hose is as high as the washer...
Asked by viresh9 - Sat Feb 17 12:06:22 2007 - - 2 Answers - 1 Comments
A. The drain hose must be up as high as the top of the machine. Ideally the drain hose should be hooked into a 2 1/2" stand pipe that is at least as high as the top of the washer. If you have the hose laying down or it has an extention added onto it and it does not loop up as high as the machine it will just allow the water to run right out of the machine as fast as it comes in. If you do have a loop up as high as the machine and the hose with an extention fastened to it and the extention goes down a floor drain the water will siphon out of the machine a siphon break must be added to the hose.
Answered by ApplianceGuy - Sun Feb 18 04:23:01 2007
Q. I've Kenmore washer 80 model # 110.92283800 and once I start the water cycle it will just drain that water. Water will not stay inside the washer... any sugggestions. Thanks I've Kenmore washer 80 model # 110.92283800 and once I start the water cycle it will just drain that water. Water will not stay inside the washer... any sugggestions. My drain hose is as high as the washer...
Asked by viresh9 - Sat Feb 17 12:06:22 2007 - - 2 Answers - 1 Comments
A. The drain hose must be up as high as the top of the machine. Ideally the drain hose should be hooked into a 2 1/2" stand pipe that is at least as high as the top of the washer. If you have the hose laying down or it has an extention added onto it and it does not loop up as high as the machine it will just allow the water to run right out of the machine as fast as it comes in. If you do have a loop up as high as the machine and the hose with an extention fastened to it and the extention goes down a floor drain the water will siphon out of the machine a siphon break must be added to the hose.
Answered by ApplianceGuy - Sun Feb 18 04:23:01 2007
clothes coming out dusty from brand new Kenmore washer?
Q. we bought a brand new Kenmore washer but when we wash our clothes all the clothes come out with a thing layer of dust stuck onto them..black clothing and white clothing are effected mostly... we have to rinse all the clothes with water again by hand in order to take the dust out..it is getting very tiring.. i was wondering if anybody knew what i could do to help the clothes come out cleaner if anybody has any handy tips that could help
Asked by inlove - Sat Aug 15 15:42:13 2009 - - 1 Answers - 0 Comments
A. try running the washer, empty, with a cup of vinegar, and see if that helps. seems way strange to me.
Answered by hippie grandma - Sat Aug 15 15:52:24 2009
Q. we bought a brand new Kenmore washer but when we wash our clothes all the clothes come out with a thing layer of dust stuck onto them..black clothing and white clothing are effected mostly... we have to rinse all the clothes with water again by hand in order to take the dust out..it is getting very tiring.. i was wondering if anybody knew what i could do to help the clothes come out cleaner if anybody has any handy tips that could help
Asked by inlove - Sat Aug 15 15:42:13 2009 - - 1 Answers - 0 Comments
A. try running the washer, empty, with a cup of vinegar, and see if that helps. seems way strange to me.
Answered by hippie grandma - Sat Aug 15 15:52:24 2009
I have a Kenmore washer #11082980110 That will not spin out the water--it agitates fine. Help?
Q. I think I should get another washer my kids think I should get parts. Can anyone help?
Asked by dona w - Thu May 17 16:04:08 2007 - - 8 Answers - 0 Comments
A. Before it can spin all the water has to drain out...possible reasons are 1 bad lid switch...2 bad pump...it is a lot cheaper to have this fixed a compared to buying a new washer
Answered by wwwstat - Thu May 17 17:36:38 2007
Q. I think I should get another washer my kids think I should get parts. Can anyone help?
Asked by dona w - Thu May 17 16:04:08 2007 - - 8 Answers - 0 Comments
A. Before it can spin all the water has to drain out...possible reasons are 1 bad lid switch...2 bad pump...it is a lot cheaper to have this fixed a compared to buying a new washer
Answered by wwwstat - Thu May 17 17:36:38 2007
What is the worst thing about the new Kenmore washer commercial?
Q. This commercial is relativly new and there is something about it that makes me sick. The first correct answers gets 10 points:)
Asked by Kit Kat - Tue Jan 23 19:29:43 2007 - - 2 Answers - 0 Comments
A. I don't know. I've never seen the commercial before. I'm guessing that it's too rowdy or something.
Answered by Katie - Tue Jan 23 19:41:27 2007
Q. This commercial is relativly new and there is something about it that makes me sick. The first correct answers gets 10 points:)
Asked by Kit Kat - Tue Jan 23 19:29:43 2007 - - 2 Answers - 0 Comments
A. I don't know. I've never seen the commercial before. I'm guessing that it's too rowdy or something.
Answered by Katie - Tue Jan 23 19:41:27 2007
Help with Kenmore Washer please?
Q. We have a Kenmore 800 series top load washer (3 years old), Model # 24872300. A few weeks ago it stopped agitating. It would pump the water out and pretty much do everything else, but stopped spinning. My husband took it apart and when he put it back together nothing worked. The repairman I called said we need a new motor. I personally think that my husband did not put it back together correctly. Not sure what to do since the motor would cost around $150. Has anyone had a similar experience with this model washer?
Asked by question33 - Fri Mar 23 12:48:09 2007 - - 1 Answers - 0 Comments
A. Evidently your husband failed to connect something when he put the machine back together. I think your model # should have been "110.24872300" which I believe is a direct drive machine. The motor runs in one direction th agitate and reverses direction to pump the water out and spin. A common failure on them is the coupling between the motor and transmission. Here are a couple of sites that might help you determine what may be wrong with your machine and ways to check different functions. I hope they help...Good Luck...
Answered by Ret68 - Fri Mar 23 15:10:47 2007
Q. We have a Kenmore 800 series top load washer (3 years old), Model # 24872300. A few weeks ago it stopped agitating. It would pump the water out and pretty much do everything else, but stopped spinning. My husband took it apart and when he put it back together nothing worked. The repairman I called said we need a new motor. I personally think that my husband did not put it back together correctly. Not sure what to do since the motor would cost around $150. Has anyone had a similar experience with this model washer?
Asked by question33 - Fri Mar 23 12:48:09 2007 - - 1 Answers - 0 Comments
A. Evidently your husband failed to connect something when he put the machine back together. I think your model # should have been "110.24872300" which I believe is a direct drive machine. The motor runs in one direction th agitate and reverses direction to pump the water out and spin. A common failure on them is the coupling between the motor and transmission. Here are a couple of sites that might help you determine what may be wrong with your machine and ways to check different functions. I hope they help...Good Luck...
Answered by Ret68 - Fri Mar 23 15:10:47 2007
What cycle gives highest water level in Kenmore Oasis HT washer?
Q. Just got a Kenmore Oasis HT washer. Already know about the lower water efficiency levels...Just tried using the SHEETS and Bulky/Bedding cycles and wonder if this is the setting with the highest water levels? Any suggestions? I bought this machine to do LARGE loads, but want to make sure clothes get clean with enough water. Pls don't tell me to get a front loader machine, because I have already heard horror stories about mold/mildew/smell. Help???!!! Forgot to add...yes, read owner's manual back and forward with no answer to my question.
Asked by snow_navigator - Thu Nov 20 22:22:47 2008 - - 1 Answers - 0 Comments
A. Maybe the owner's manual would help you.
Answered by sweetpea - Fri Nov 21 00:37:56 2008
Q. Just got a Kenmore Oasis HT washer. Already know about the lower water efficiency levels...Just tried using the SHEETS and Bulky/Bedding cycles and wonder if this is the setting with the highest water levels? Any suggestions? I bought this machine to do LARGE loads, but want to make sure clothes get clean with enough water. Pls don't tell me to get a front loader machine, because I have already heard horror stories about mold/mildew/smell. Help???!!! Forgot to add...yes, read owner's manual back and forward with no answer to my question.
Asked by snow_navigator - Thu Nov 20 22:22:47 2008 - - 1 Answers - 0 Comments
A. Maybe the owner's manual would help you.
Answered by sweetpea - Fri Nov 21 00:37:56 2008
My Kenmore washer will not agitate or spin?
Q. It will fill and drain. Is there any way to get it repaired or will I just have to get a new washer?
Asked by kat - Mon Dec 28 13:08:46 2009 - - 5 Answers - 0 Comments
A. It is possible that the motor coupling is broken. check the following site to see how to check it. It also has a video on how to fix it. Kenmore is made by Whirlpool. ...Good Luck...
Answered by Ret68 - Mon Dec 28 13:54:46 2009
Q. It will fill and drain. Is there any way to get it repaired or will I just have to get a new washer?
Asked by kat - Mon Dec 28 13:08:46 2009 - - 5 Answers - 0 Comments
A. It is possible that the motor coupling is broken. check the following site to see how to check it. It also has a video on how to fix it. Kenmore is made by Whirlpool. ...Good Luck...
Answered by Ret68 - Mon Dec 28 13:54:46 2009
My kenmore washer is leaking at the end of the wash cycle when there are three separate surges of water. Help!?
Q. Can anyone tell me what is going on when this water comes into the tub? That might help me figure out where the leak is coming from. It leaks from underneath the front (slightly right) of the washer.
Asked by Patricia - Thu Apr 8 18:20:17 2010 - - 2 Answers - 0 Comments
Q. Can anyone tell me what is going on when this water comes into the tub? That might help me figure out where the leak is coming from. It leaks from underneath the front (slightly right) of the washer.
Asked by Patricia - Thu Apr 8 18:20:17 2010 - - 2 Answers - 0 Comments
From Yahoo Answer Search: 'kenmore washer'
Sat Jul 3 07:34:43 2010 [ refresh local cache ]
